Davey and Company

Bronze Drain Plugs - Davey

Bronze drain plugs with screw plug insert, complete with rubber seal, available in a range of sizes. The thread is drilled so that when loosened, the plugs allow a small amount of water to drain.  Unscrew the plug completely for higher water...

Davey and Company

Bronze Snap Shackles - Swivel Eye

Forged manganese bronze snap shackles with a swivel eye.  These bronze shackles are manufactured to a high standard in England. Available in a variety of sizes and safe working loads as set out below: SKU Overall Length Safe Working Load Davey's...

Davey and Company

Bronze Snap Shackles - Fixed Eye

Forged manganese bronze snap shackles with a fixed eye.  These quality shackles are manufactured to a high standard in England and have numerous marine applications. Available in a variety of sizes and safe working loads as set out...

Davey and Company

Bronze Stemhead Fitting - Lightweight

Cast bronze stem head fitting for sailing dinghies up to around 12' in length.  Note that this fitting is cast at an 80° angle and it is recommended to not attempt bending. These attractive fittings are made in England and can be fastened with 4...

Davey and Company

Bronze Eyes on Plate - Square

English-made quality bronze eye plates (or sash eyes) in a choice of rumbled bronze, polished bronze or chrome plated bronze finishes. These plates are ideal as tie-off points for fenders or deck lines. SKUFinishPlate SizeHeightRing Inside...

Davey and Company

Bronze Eyes on Diamond - Small

Cast from gunmetal bronze and made in the UK, these beautiful diamond eye plates are for lighter duties, such as attaching fender lines. With a diamond-shaped base, these bronze plates can be fastened with 8-gauge silicon bronze wood screws...

Davey and Company

Bronze Shell Vent

Stylish bronze vent commonly used for ventilating engine bays on timber motor boats. Part of the Davey range of boat hardware from England, these vents can be fitted with or without the included trim ring.  The trim ring is a separate component that...

Davey and Company

Mushroom Vents - Low Domed Pattern

Smaller low-profile mushroom ventilators with a domed profile.  Cast in bronze, these UK-made vents have a low spigot and are ideal for mounting flush to cabin tops and other areas unlikely to become awash. Their low, domed-profile means sheets will...

Davey and Company

Mushroom Vents - Low Flat Pattern

Smaller low-profile mushroom ventilators with a flat profile.  Cast in bronze, these UK-made vents mount flush to cabin tops.  With a lower spigot height they are more suited to areas unlikely to become awash. The ventilator can be operated...

Davey and Company

Davey Bronze Open Top Cleats

Solid bronze open top cleats made in England by Davey & Co. These cleats are beautifully cast and polished. Their open top design makes open top cleats useful as both a cleat and part-time fairlead. Available in a range of sizes and can be chrome...

Davey and Company

Brass Sailing Dinghy Sliding Gooseneck

A quality sliding gooseneck fitting suitable for traditional sailing dinghies and other small boats. Made of brass, this sailing boat fitting consists of a spike on a gooseneck with tangs for fixing a shackle.  The spike requires a 12mm x 12mm...

Davey and Company

Bronze Lightweight 4-Piece Rudder Kit - Single Strap

Single strap bronze rudder kit suitable for lightweight dinghies of up to about 8 feet long. Made in England, this 4-piece set is beautifully cast and polished. The set consists of two transom-mounted gudgeons and two rudder-mounted pintles. The rudder...

Flat Head Silicon Bronze Nails 19mm x 1.6mm (per 100g)

Flat Head Silicon Bronze Nails 19mm x 1.6mm (per 100g) New Zealand-made silicon bronze flat-head nails, 19mm in length, with a 1.6mm annular (ringed) grooved shaft ensuring a tight grip. Otherwise known as "gripfast" or ring barb nails.  Ideal for...

Flat Head Silicon Bronze Nails 25mm x 1.6mm (per 100g)

Flat Head Silicon Bronze Nails 25mm x 1.6mm (per 100g) New Zealand-made silicon bronze flat-head nails, 25mm in length, with a 1.6mm annular (ringed) grooved shaft ensuring a tight grip. Otherwise known as "gripfast" or ring barb nails.  Ideal for...

Yushung Fasteners

Silicon Bronze Machine Screw - Flat Slot Head 8-32 UNC x 2"

Silicon bronze machine screws are like threaded bolts with a flat countersunk slotted screw head. Ideal for securing our bronze boat hardware through the deck, these 8g bronze machine screws have a standard UNC thread with 32 threads per inch...

Yushung Fasteners

Silicon Bronze Machine Screw - Flat Slot Head - 6-32 UNC x 2"

Silicon Bronze Machine Screw - Flat Slot Head 6-32 UNC x 2" Silicon bronze machine screws are like threaded bolts with a flat countersunk slotted screw head. Ideal for securing our bronze boat hardware through the deck, these 6-gauge bronze machine...

Flat Head Silicon Bronze Nails 50mm x 2.8mm (per 100g)

Flat Head Silicon Bronze Nails 50mm x 2.8mm (per 100g) High-quality New Zealand-made silicon bronze flat-head nails with an annular (ringed) grooved shaft ensuring a tight grip. Otherwise known as "gripfast" nails or ring barb nails.  Ideal for...

MURRAY - Traditional Winches & Marine Hardware

Chromed Bronze Separating Hinges (pair)

Famous "snap-apart" or separating hinges. These quality bronze hinges have a sprung centre pin to enable quick removal without the use of tools.  They work exactly like normal hinges, but pull the sprung pin on each hinge and simply remove the...

Manganese Bronze Thimble - Closed

Quality New Zealand-made closed thimbles cast in manganese bronze. The 45mm thimble will take up to a 10mm rope, while the 67mm will take up to 14mm rope diameter under tension. SKU Overall Length Max Width Suits Rope Weight WHT-MW220 45mm 27mm Up...

Copper Sheet (0.55mm)

Copper Sheet (0.55mm) Copper sheet with a gauge of 0.55mm for sheathing wooden boat hulls, roofing and many other marine and household applications. For sheathing a wooden boat the copper sheets are overlapped and fixed in place using smooth-shafted...